In This Article

How Often Should Barbers Clean Clippers

Barbershops are often seen as places where men go to get their hair cut and styled. However, barbers also have a responsibility to keep their clippers clean. According to the American Bar Association, barbers should clean their clippers every time they use them, whether they are cutting hair or shaving. This will ensure that the blades are in good condition and that the salon’s air quality is not negatively impacted.

The Different Types of Clippers

There are different types of clippers, and each requires its own maintenance schedule. Here’s a rundown of how often each type should be cleaned:

Electric Clippers:

-Every 3 to 4 months.

-If the blade starts to feel rough, it needs to be sharpened. To do this, take off the blade and place it in a grinding stone until it’s sharp. Then reattach the blade to the clipper.

Hand-held Clippers:

-Every 2 weeks.

-The blades on hand-held clippers can usually last for about 6 months before they need to be replaced. If you notice that the blades aren’t cutting as well as they used to, it’s time to replace them.

Dryer Shears:

-Every month.

-To keep your dryer shears in good condition, it’s important to clean them every month. To do this, remove the blades and wash them in warm soapy water. Be sure to dry them completely before reassembly.

The Basics of Clipper Care

Clippers can last for years with proper care – but how often should they be cleaned?

The average barber shop clipper will last around 5-7 shaves before needing to be replaced. It is recommended that clippers be cleaned and oiled every 2-3 shaves.

To clean a clipper:

1. Remove the blade and comb from the clipper.

2. Wet a cloth with dish soap and wring out the excess.

3. Place the cloth over the blade and comb, and use a gentle back and forth motion to clean both surfaces. Pay attention to the cutting edge of the blade and comb.

4. Dry the clipper blades and comb with a clean cloth. Apply a small amount of oil to the blades before re-inserting them into the clipper.

The Importance of Cleaning Clippers

Barbers have long been known for their impeccable haircuts, but the tools that they use to get those looks – clippers – can also be dirty and dangerous.

A clean haircut starts with a clean clipper. Here’s how often barbers should clean their clippers:

– Every two weeks if you’re using standard-grade blades

Cleaning is essential to keep your clippers in good condition, and it will also help prevent hair from build-up and debris from getting stuck in the blades. Here are a few tips for cleaning your clippers:

– use a brush to remove any built-up dirt or hair

– dry them off completely before storing

How Often to Clean Clippers

A good rule of thumb is to clean your clippers every time you use them. This will help reduce the spread of air-borne bacteria and keep them operating at their best. Additionally, keeping your clippers clean will help prevent tangles and snags that can lead to cuts.

Even if your clippers are not cutting as well, they can be fixed by cleaning them with warm water and mild soap. This should be done over a sink and the clippers need to be thoroughly cleaned before storing them away.

The Signs That It’s Time to Clean Your Clippers

If you notice any of the following signs that your clippers need to be cleaned, it’s time to take them in for a tune-up:

-Your clippers aren’t cutting as smoothly as they used to
-The tips of your blades are becoming rusty or covered in hair
-The comb is starting to come off or look worn out
-The combs on your other barber tools are getting dirty too if you see any of these signs, it’s time to take your clippers in for a tune-up. A clean clipper will help them work more smoothly and last longer.

How to Clean Your Clippers the Right Way

When it comes to keeping your clippers clean and sharp, experts agree that you should clean them at least once a week. Here’s how:

– Wet the clipper blades with water and swish around to get rid of excess.

– Put the clippers in a sealable bag or container and pour in enough rubbing alcohol to cover the blades.

– Shake the container frequently until the blades are coated.

– Rinse the blades with water and dry them off.

– Wash the blades of the clippers with water


Cleaning your clippers regularly is essential to keeping them in good condition and ensuring that they can cut hair effectively. Here are a few guidelines on how often you should clean your clippers:
-If you use them every day, clean them once a week
-If you use them twice a week, clean them once every two weeks
-If you use them three times a week, clean them once every three weeks